你知道在進行搭建山東電纜橋架的目標，如何判斷地面的距離比較合理，能夠契合工人師父的整體設計規劃呢，讓我們蘇鑫橋架工作人員帶領大家學習一下吧。

　　You know how to judge the reasonable distance between the ground and the overall design plan of the worker Shifu when building the cable tray in Shandong. Let us Su Xin bridge staff lead you to learn.

　　使用“激光投線儀”確認頂棚通桿螺絲的位置，并使用電鉆進行開孔。上圖激光投線儀，確認安裝支架支吊架位置。

　　Use a "laser line projector" to confirm the position of the ceiling through rod screws and use an electric drill for drilling. Confirm the position of the installation bracket support and hanger for the laser line projector shown above.

　　安裝支架支吊架間距為3米，在直線與彎通連接處0.3米的位置使用吊架。安裝支架的安裝高度為2.5米。

　　Install brackets with a spacing of 3 meters between supports and hangers, and use hangers at a position of 0.3 meters at the connection between straight lines and bends. The installation height of the bracket is 2.5 meters.

　　確認通桿螺絲位置時建議比原來長度稍長幾公分確?？梢孕》日{整安裝支架水平位置。 五、使用拉爆與通桿螺絲相結合將通桿螺絲固定在頂棚確定的位置，并在通桿螺絲的下端安裝吊框，吊框選用安裝支架廠商提供的原件。

　　When confirming the position of the through-hole screw, it is recommended to extend it a few centimeters longer than the original length to ensure that the horizontal position of the installation bracket can be adjusted slightly. 5、 Use a combination of pull-out and through-pole screws to fix the through-pole screws at the designated position on the ceiling, and install a hanging frame at the lower end of the through-pole screws. The hanging frame is selected from the original components provided by the installation bracket manufacturer.

　　安裝支架連接處一端安裝支架連接片上螺絲不上即可安裝支架直線段安裝時，直接將安裝支架穿過吊框，連接縫使用聯接片連接。

　　At one end of the installation bracket connection, if the screw on the bracket connection piece is not tightened, the bracket can be installed. When installing the straight section of the bracket, directly pass the installation bracket through the hanging frame, and use the connection piece to connect the connection seam.

　　并安裝跨界軟銅線：安裝支架位置矯正與檢查確保安裝支架安裝完成之后處于水平位置，如不符合要求應當立即進行調整。確保安裝支架前端與后端處于同一直線上，如不符合要求立即進行調整。

　　And install cross-border flexible copper wire: correct and check the position of the installation bracket to ensure that it is in a horizontal position after installation. If it does not meet the requirements, it should be adjusted immediately. Ensure that the front and rear of the installation bracket are in the same straight line, and adjust immediately if they do not meet the requirements.

　　總之，山東電纜橋架的搭建需要確保安裝支架連接處應有軟通線連接，如沒有應當立即增加。確保安裝支架某一直線段起始端與末端應當有角鐵加進行固定，安裝支架超過一定距離時應當選用角鐵支架進行固定。

相關文章：山東電纜橋架